?

We use the time winding machine will encounter some problems, especially with winding machine a few years later would be more prone to various problems. Our problems are generally divided into 2 categories.

?

1.是硬件問題。2是設置問題。

?

The 1 is a hardware problem. The 2 is to set a question.

?

首先我們要看狀況分析問題的所在。變壓器繞線機比如以自動繞線機我們舉例幾個常見的問題。

?

We want to see the situation analysis problem first place. Such as automatic winding machine and we illustrate several common problems.

?

1、拍線不整齊。我們要根據情況分析是在正常加工的時候出現問題，還是換了產品調試過之后出現的問題。前者一般屬于硬件問題。后者一般是設置問題。硬件問題一般是工裝夾具松動、排線機構緊固螺絲松動、排線機構潤滑不佳導致步進電機負載過重步進電機失步所引起排線不整齊。

?

1, strings not neat. We according to the situation analysis is the time in the normal processing of the problems, or exchange the product after debugging problems. The former belongs to the hardware problem. The latter is generally set problems. The hardware problem is generally fixture loosening fastening screw loosening, a winding mechanism, a winding mechanism due to poor lubrication of stepping motor overload of step motor caused by irregular line.

?

2、主軸停車位置不精準。主軸停車位置不精準一般都是由于剎車故障引起。比如剎車片松動，或者剎車片磨損引起。也與剎車時間的設置有關，剎車時間過短也會出現主軸停車位置不準。需要更換剎車片或。進行剎車時間調整。

?

2, the parking position is not accurate. The parking position is not accurate in general are due to brake failure caused by. Such as brake loose, or brake pad wear caused by. Also related to braking time, braking time is too short will also appear spindle parking location not. Need to replace the brake pads or. Brake adjustment.

?

3、繞線圈數不準、繞線機如出現計數不準，http://4888123.com/一般由于傳感器、或控制器的硬件問題、出現這種情況繞線機無法工作，一般是通知生產廠家進行維修解決。

?

3, coil number are not allowed, winding machine such as inaccurate counting, generally due to the sensor, or hardware problem, appear this kind of circumstance winding machine can not work, the general is to inform the manufacturer for repair solution.